Тема: WeTek Play Android DVB-S2 Satellite Receiver ENIGMA2

[joker2™]

Процессор – Amlogic AML8726-MX dual core Cortex A9 @ 1.5GHz with a dual core Mali-400MP GPU
Оперативная память – 1GB DDR3
Основная память – 4 GB NAND flash + 1x micro SD slot
Видео выход – HDMI, AV (CVBS + R/L audio)
Аудио выход – HDMI, AV, and optical S/PDIF
Тюнер – DVB-S2, or DVB-C/DVB-T/DVB-T2
Передача данных – 10/100M Ethernet, 802.11 b/g/n Wi-Fi , and Bluetooth 4.0 (AP6210)
Порты USB – 3x external USB 2.0 ports, 2x internal USB 2.0 ports
Разное – IR приемник, 3 LEDs для питания, Ethernet и Wi-Fi, RS-232 для последовательного порта.
Питание – 12V/1.5A


Поддержка Ш@ры по протоколам CCCAM, Newcamd и Biss ключей


Поддержка Русского языка + 24 других


Комплектация Инструкция, RCA - кабель, Пульт ДУ, HDMI - кабель, Блок питания 220 v


Поддержка AirPlay, поддержка XBMC и Torrent TV, поддержка внешней клавиатуры, мыши, жесткого диска и др. USB - устройств

[joker2™]

enigma2 на ресивере

[joker2™]

wetek setup tvheadend dvb-s 28.2E and oscam + wecloud antenna

[joker2™]

WeTek Play: First Android mini-pc running Lollipop 5.0.2

[joker2™]

WeTek Play
OpenELEC-WeTek_Play.arm-devel-20150426095441 r20720 g906b503 Kodi 15

[TopichTV]

Enigma 2 для WeTek Play



DreamSet Edit 2.4.4 Beta 7

Код: Извините, но гости не могут просматривать ссылки. Регистрация или Логин

www.dreamset-editor.com/files/Dreamset244Beta7.zip

[TopichTV]

Учебник по использованию WeTek Play в качестве стримера IPTV с помощью MuMuDVB, UDPXY и OSCam

Код: Извините, но гости не могут просматривать ссылки. Регистрация или Логин

So what you will need:

1. WeTek Play with DVB Tuner (DVB-S2 or DVB-C/T/T2 tuner)

2. OpenELEC 5.0.X (latest version is 5.0.6) installed on NAND Flash or microSD card

3. PC/Mac (of course :D)

After you install OpenELEC, and you boot in to it, enable Un-official OpenELEC repo for WeTek Play, to do it go to:

System -> Add-ons -> Get Add-ons -> OpenELEC MediaCenter OS Add-ons -> Addons Repository -> Unofficial OpenELEC (WeTek_Play/arm) Add-ons , open it, and press OK/Enter on Install.

After you done that, move back to Add-ons main menu, and press OK/Enter on Check for updates (sometimes is needed to do this for two times, as Kodi know to reboot itself at this process).

Once when You make "check for updates" go to System -> Add-ons -> Get Add-ons -> Unofficial OpenELEC (WeTek_Play/arm) Add-ons -> Program Add-ons

and once when you are in Program Add-ons, install udpxy and mumudvb apps. Of course, if you will use OSCam, install it from Unofficial repository, it is located in Service Add-ons.

Once when mumudvb and udpxy are installed, please connect by SSH to your WeTek Play device (username is root, password is openelec).

Execute this commands:

. etc/profile

. /etc/profile

ifconfig lo multicast

ip route add 224.0.0.0/4 dev lo src 127.0.0.1

ip route flush cache

With above commands, you configured WeTek Play to handle multicast traffic and to redirect it to loopback interface, and of course this will prevent multicast traffic to "kill" traffic on your LAN network.

Now let's configure/make mumudvb conf file.

On SSH execute this commands:

touch /storage/videos/mumudvb.conf

nano /storage/videos/mumudvb.conf

Depending of what type of DVB Tuner you are using with your WeTek Play, here are few examples how your config will look.

DVB-S/S2 Tuner 1:

card=0
tuner=0
multicast_ipv4=1
autoconfiguration=full
freq=__tranponder frequency in MHz__
pol=__polarisation H, V, L or R__
srate=__symbol rate__

DVB-S/S2 example Tuner 1:

card=0
tuner=0
multicast_ipv4=1
autoconfiguration=full
freq=11785
pol=h
srate=27500

In case you want to configure Tuner 2 (LNB 2), set : card=1
In case you want to use OSCam to descramble channels add parameter: scam_support=1

When you finished with editing your mumudvb.conf press on keyboard CTRL+O, press Y and then press CTRL+X.

Finally when all is setup, we can run MuMuDVB with this command:

mumudvb -d -c /storage/videos/mumudvb.conf

Now you will see messages from MuMuDVB tuning to frequency, then catching channels, and then listing them with their Multicast IP addresses.

Open second SSH session to WeTek Play, and execute this command:

udpxy -T -p 82 -m lo -c 64

Now udpxy, will convert multicast streams to unicast, so you can open them in VLC player as:

You can see links before reply

More information about configuring MuMuDVB can be foun here:

You can see links before reply

Of course if you have Linux PC or Windows PC with ffmpeg installed, you can use it to transcode streams in MPEG-4 H264 streams with AAC audio, but all of this depends on CPU power of your PC. In theory I was able to transcode 15 to 20 SD channels per single Intel Core i7 4770 CPU with 4 GB RAM, running on Debian 7.0 with installed latest ffmpeg with x264 from source.


For DVB-C/T/T2 Tuner streaming from DVB-C source:

card=0
tuner=0
elivery_system=DVBC_ANNEX_AC (can be DVBC_ANNEX_B)
multicast_ipv4=1
autoconfiguration=full
freq=__tranponder frequency in MHz__ (e.g 414)
srate=__symbol rate__ (e.g 6875)
coderate=auto

For DVB-C/T/T2 Tuner streaming from DVB-T/T2 source:

card=0
tuner=0
delivery_system=DVBT (can be DVBT2 for DVB-T2)
multicast_ipv4=1
autoconfiguration=full
freq=__tranponder frequency in MHz__ (e.g 414)
bandwidth=8MHz (can be 8MHz, 7MHz, 6MHz, auto (DVB-T2: 5MHz, 10MHz, 1.712MHz)
coderate=auto

[guffi_kaa]

Доброго дня.
А это чудо продаётся только на али? И ещё вопрос, можно где нибудь заказать dvb-t2 тюнер отдельно для этого девайса. Хочу побаловаться с S2  и потом поменять на T2

[joker2™]

сайт производителя Извините, но гости не могут просматривать ссылки. Регистрация или Логин

[joker2™]

WETEK WETEKPlay Proof of Conzept openATV 5.0