Тема: Официальная карта НТВ+ на Dreambox/Tuxbox

[Tehnics™]

Карта активируется на OScam+MGcamd, NewCS+Mgcamd - проверено или на виа ресивере

[pashaa™]

Но первичную активацию(на совсем новую карту) все таки нужно наверно в рекомендованом оборудовании сделать.

[MIRAGE]

Возможно карта и активируется на эму кард серверах(хотя непроверял) но возрастное ограничение уж точно не снимается. здесь либо ресивер с виа либо скрипт прогонять.

[Ligioner]

как активировать оф карту +++, для последущей работы на туксе 908л?

Новые карты активируются в дримах без проблем ( oscam+ mg_camd)
На счёт карт которые идут с привязкой не знаю , не пробовал
Если у тебя такая карта попробуй в дриме активировать , только кардсервер нужно правильно настроить , в противном случае ты ни чего не потеряешь , позвонишь и запросишь повторную активацию
Я карты радуги и триколор  без проблем активирую в дримах , карты орионовские старые на пакет переходной   заметил что в каком ресивере активируешь потом только в нём и работает , вставляю в другой дрим нет картинки , хотя лог нормальный

[dizh]

немного с запозданием, но тоже подтвержу, новая белая карта пришедшая на замену, активировалась в туксе908 на мгкамд\ньюцс1,67. за минуты две-три.

[MIRAGE]

а возрастное ограничение?

[kazlift]

Подскажите в чём может быть дело.В воскресенье глюкнул ресивер Дрим 7025.После выдачи ошибки на однородном фоне,он поидее должен был перезагрузиться.Пошёл на перезагрузку,потом появился новый глюк.Ресивер при включении стал показывать заставку Джемини с надписью ЛОДИНГ и затем появлялся однородный фон (синий к примеру),затем снова заставка и фон,но уже другого цвета и так до бесконечности.

Решил перепрошить его.До этого тоже Джемини стаяла,только не помню какая версия,толи 3.9 толи 4.2 .Поставил 4.7,установил эмулятор МЖКамд 1.31 и newcs1.67.Ставил вручную из ранее скаченных архивов.До этого ставил через инет,теперь видимо с сервера Джемини их убрали.

Имею карточку НТВ+ и расшариваю её для самого себя,чтобы использовать второй тюнер встроенный в ресивер (Дрим 7025 двухтюнерный).Т.к. пакет через карту у меня базовый,недостающие каналы смотрю через шару.Теперь собственно сама проблема.

После перепрошивки и установки эмулятора,вбил ранее сохранёные настройки.Всё заработало.Радовался как ребёнок,до вечера пока логи работы Мжкамда не посмотрел через 3Сислог и ахренел,всё это время работала только шара,карта тупо молчала.Привожу лог работы Мжкамда с отключённой шарой,чтобы более понятно было

Код: Извините, но гости не могут просматривать ссылки. Регистрация или Логин

Feb 14 08:26:38 192.168.1.3 [mg0] namespace 1680000 t-id 1 on-id 70
Feb 14 08:26:38 192.168.1.3 [mg0] descramble on 5, source 2
Feb 14 08:26:38 192.168.1.3 [mg0] service 277C index 0 pmt pid 6C (1)
Feb 14 08:26:38 192.168.1.3 CaPID: 0x07D8 ProvID: 040600
Feb 14 08:26:38 192.168.1.3 CaPID: 0x0FA8 ProvID: 023700
Feb 14 08:26:38 192.168.1.3 [mg0] No viaccess key(s) found for id 40600 keynr 08
Feb 14 08:26:38 192.168.1.3 [mg0] network can't decode
Feb 14 08:26:38 192.168.1.3 [mg0] pid 0x07D8 failed to decode.
Feb 14 08:26:38 192.168.1.3 [mg0] No viaccess key(s) found for id 23700 keynr 08
Feb 14 08:26:38 192.168.1.3 [mg0] network can't decode
Feb 14 08:26:38 192.168.1.3 [mg0] pid 0x0FA8 failed to decode.
Feb 14 08:26:38 192.168.1.3 [mgcamd] emm started
Feb 14 08:26:38 192.168.1.3 CaPID: 0x03EB ProvID: 030600
Feb 14 08:26:38 192.168.1.3 CaPID: 0x03E8 ProvID: 023700
Feb 14 08:26:38 192.168.1.3 CaPID: 0x03ED ProvID: 040610
Feb 14 08:26:38 192.168.1.3 CaPID: 0x03EC ProvID: 040600
Feb 14 08:26:38 192.168.1.3 CaPID: 0x03EA ProvID: 040620
Feb 14 08:26:38 192.168.1.3 [mgcamd] emm stopped
Feb 14 08:26:57 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:26:57 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (23ms)
Feb 14 08:27:18 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:27:18 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (3ms)
Feb 14 08:27:39 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:27:39 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (33ms)
Feb 14 08:28:00 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:28:00 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (20ms)
Feb 14 08:28:21 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:28:21 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (11ms)
Feb 14 08:28:42 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:28:42 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (41ms)
Feb 14 08:29:03 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:29:03 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (0ms)
Feb 14 08:29:24 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:29:24 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (30ms)
Feb 14 08:29:45 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 14 08:29:45 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (9ms)

Вот что в нюкамд листе

Код: Извините, но гости не могут просматривать ссылки. Регистрация или Логин

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 192.168.1.3 10001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
#CWS = шара 4000 логин пароль 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserv

Вот что в newcs.xml

Код: Извините, но гости не могут просматривать ссылки. Регистрация или Логин

<?xml version="1.0"?>
<newCSconfig>
<readers name="Dreambox SCI">
<device>
<name>?????? ???? ??????????????</name>
<type>sci</type>
<node>/dev/sci0</node> <!-- ??? ????????? ? 1 ??????????????? ???? ???? ???? ????? ???????????? -->
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<PTShandshake>No</PTShandshake> <!-- ??? ???? Viaccess ?????? ???????? Yes, ??? ???????? ???????? ?????? ?????-->
<carddetect>no</carddetect>
<newcamd_port>10000</newcamd_port> <!-- ???? ? ???????? ?? ????? ????????? ????? ? ????? ?????-->
<autosid>No</autosid>
<priority>round</priority>
</device>
<device>
<name>??????? ???? ??????????????</name>
<type>sci</type>
<node>/dev/sci1</node> <!-- ??????? ???? ?????????????? ????? ?????? ??? Dreambox, 7000,7020,7025,8000 -->
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<PTShandshake>No</PTShandshake>
<carddetect>no</carddetect>
<newcamd_port>10001</newcamd_port>
<autosid>No</autosid>
<priority>round</priority>
</device>
</readers>
<radegastserver>
<enabled>No</enabled>
<port>10003</port>
<allow>
<hostname>localhost</hostname>
</allow>
</radegastserver>
<cache>
<emm>20</emm>
<ecm>-1</ecm>
</cache>
<httpd>
<server>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>newcs</name>
<password>newcs</password>
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<password></password>
<mode>normal</mode>
<level>normal</level>
<type>init</type>
<output>console,tcp</output>
<tcp_port>1001</tcp_port>
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<enabled>Yes</enabled>
<name>newcs</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>local</name> <!-- ?????, ??? ????????? ??????? ???? ?? ?? MGcamd (????? ???? ?????) -->
<password>local</password> <!-- ??????, ??? ????????? ??????? ???? ?? ?? MGcamd (????? ???? ?????) -->
<hostname>192.168.1.3</hostname>
<au>on</au> <!-- ??????? ?????? ????? ?????????? ???????????? -->
</user>
<user>
<name>root</name> <!-- ?????, ??? ????????? ??????? (?????? ??????? ?? ????, ???? ????? ????????) -->
<password>azbox</password> <!-- ??????, ??? ????????? ??????? (?????? ??????? ?? ????, ???? ????? ????????) -->
<au>off</au> <!-- ???????? ?????? ????? ?????????? ???????????? -->
</user>
</newcamdserver>
</newCSconfig>
Вот оригинал https://*****-sat.net/forums/index.php?s…=findpost&p=396


Срисовал с гомель сата,до глюка всё работало как часы.

Задал на Гомеле этот вопрос,мне упирают на то,что у меня локальный IP указан не верно.Хотя вроде всё верно вбил.

Вот воскресный лог если что:

Код: Извините, но гости не могут просматривать ссылки. Регистрация или Логин

Feb 13 20:05:13 192.168.1.3 got 8 cmd 9F
Feb 13 20:07:27 192.168.1.3 tuxbox mgcamd v1.31 by mixvt (compiled Oct 29 2008 19:11:00)
Feb 13 20:07:27 192.168.1.3 [mg] Net:1:3:2:4s Show ecm:1, emm:1 Up:5 Au:2 Dir:0 Osd:no:80:0 Cache:0 Log:1:192.168.1.2:514 Reread:0
Feb 13 20:07:27 192.168.1.3 [mg] Ecm cache time: 15
Feb 13 20:07:27 192.168.1.3 Box type: mips dreambox (dm7025, dm800)
Feb 13 20:07:27 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 13 20:07:27 192.168.1.3 SoftCam.Key error 2: No such file or directory
Feb 13 20:07:27 192.168.1.3 AutoRoll.Key error 2: No such file or directory
Feb 13 20:07:27 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 13 20:07:27 192.168.1.3 [config] newcamd route = local:192.168.1.3:10001 server newcs
Feb 13 20:07:27 192.168.1.3 [config] newcamd route = local:192.168.1.3:10000 server newcs
Feb 13 20:07:27 192.168.1.3 newcamd keep alive: 300, incoming port: 12000
Feb 13 20:07:27 192.168.1.3 [mgcam] emm thread started
Feb 13 20:07:27 192.168.1.3 [mgcamd] tps update started.
Feb 13 20:07:27 192.168.1.3 /var/keys/tps.bin error 2: No such file or directory
Feb 13 20:07:27 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 13 20:07:27 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10000...
Feb 13 20:07:27 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (45ms)
Feb 13 20:07:27 192.168.1.3 [newcamd] Connection to 192.168.1.3:10000 failed (46ms)
Feb 13 20:07:30 192.168.1.3 got 8 cmd 9F
Feb 13 20:07:30 192.168.1.3 got 150 cmd 9F
Feb 13 20:07:30 192.168.1.3 [mg0] namespace 1680000 t-id 6 on-id 70
Feb 13 20:07:30 192.168.1.3 [mg0] descramble on 5, source 2
Feb 13 20:07:30 192.168.1.3 [mg0] service 5083 index 0 pmt pid 9C (2)
Feb 13 20:07:30 192.168.1.3 CaPID: 0x07DB ProvID: 040600
Feb 13 20:07:30 192.168.1.3 CaPID: 0x0FAB ProvID: 023700
Feb 13 20:07:30 192.168.1.3 [mg0] No viaccess key(s) found for id 40600 keynr 08
Feb 13 20:07:30 192.168.1.3 [mg0] network can't decode
Feb 13 20:07:30 192.168.1.3 [mg0] pid 0x07DB failed to decode.
Feb 13 20:07:31 192.168.1.3 [mg0] No viaccess key(s) found for id 23700 keynr 08
Feb 13 20:07:31 192.168.1.3 [mg0] network can't decode
Feb 13 20:07:31 192.168.1.3 [mg0] pid 0x0FAB failed to decode.
Feb 13 20:07:31 192.168.1.3 [mgcamd] emm started
Карта отдельно работает,проверял через CI модуль.


Пробовал настройки Миража выложенные на 4 странице,тоже ничего.Вот лог:

Код: Извините, но гости не могут просматривать ссылки. Регистрация или Логин

Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ Box detect ] Box type 6 (Dream Multimedia (MIPS) Box)
Feb 16 00:25:05 192.168.1.3  for device 0 (lower) not present, defaulting to NO
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ Config ] /dev/sci0 ECM priority: round
Feb 16 00:25:05 192.168.1.3  not present, defaulting EMM: 20, ECM: Dynamic
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ Newcamd ] Server name : newcs
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ Newcamd ] Des key     : 0102030405060708091011121314
Feb 16 00:25:05 192.168.1.3  not present for User: dreambox, defaulting to NO
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] No username or password in user section, skipping...
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ Newcamd ] User 2: dreambox, Pass: dreambox, Host none, Port: 0, Au: On, Spider allowed: No, Sidoverride: No, level: 0
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ httpd ] httpd-user: newcs, password: newcs, accesslevel: admin
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ EMM Cache ] Initialising dynamic Cache
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] [ ECM Cache ] Initialising dynamic Cache
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] Calibrating delay loops
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] usleep(5) takes: 0 s 13 us
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] usleep(10) takes: 0 s 17 us
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] usleep(100) takes: 0 s 107 us
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] usleep(500) takes: 0 s 507 us
Feb 16 00:25:05 192.168.1.3 [ 00:25:10 ] Allocation memory for 200 regular users
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ Loader ] Starting Telnet on port 0
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ SockSrv ] Server thread started
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ Loader ] Started HTTP-server on port: 8080
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ Loader ] Reader type 5 on node /dev/sci0
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ Sci ] Closing device /dev/sci0 [Handle=-1]
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ Sci ] Opening device /dev/sci0
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ Sci ] resetting card now
Feb 16 00:25:05 192.168.1.3 [ 00:25:11 ] [ Sci ] Reset 
Feb 16 00:25:08 192.168.1.3 [ 00:25:14 ] [ Sci ] NO ATR Received 
Feb 16 00:25:08 192.168.1.3 [ 00:25:14 ] [ Sci ] Card reset
Feb 16 00:25:15 192.168.1.3 [ 00:25:20 ] [ Sci ] No ATR received. resetting again
Feb 16 00:25:15 192.168.1.3 [ 00:25:20 ] [ Sci ] Reset 
Feb 16 00:25:18 192.168.1.3 [ 00:25:23 ] [ Sci ] NO ATR Received 
Feb 16 00:25:20 192.168.1.3 tuxbox mgcamd v1.31 by mixvt (compiled Oct 29 2008 19:11:00)
Feb 16 00:25:20 192.168.1.3 [mg] Net:1:1:2:5s Show ecm:1, emm:1 Up:0 Au:1 Dir:0 Osd:no:80:0 Cache:7 Log:1:192.168.1.2:514 Reread:0
Feb 16 00:25:20 192.168.1.3 [mg] Ecm cache time: 15
Feb 16 00:25:20 192.168.1.3 Box type: dreambox
Feb 16 00:25:20 192.168.1.3 /dev/dvb/card0/ca0 error 2: No such file or directory
Feb 16 00:25:20 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 16 00:25:20 192.168.1.3 SoftCam.Key error 2: No such file or directory
Feb 16 00:25:20 192.168.1.3 AutoRoll.Key error 2: No such file or directory
Feb 16 00:25:20 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 16 00:25:20 192.168.1.3 [config] newcamd route = dreambox:127.0.0.1:10000 server server
Feb 16 00:25:20 192.168.1.3 newcamd keep alive: 0, incoming port: 0
Feb 16 00:25:20 192.168.1.3 [mgcam] emm thread started
Feb 16 00:25:20 192.168.1.3 [mgcamd] tps update started.
Feb 16 00:25:20 192.168.1.3 /var/keys/tps.bin error 2: No such file or directory
Feb 16 00:25:20 192.168.1.3 [newcamd] Connecting to 127.0.0.1:10000...
Feb 16 00:25:20 192.168.1.3 [newcamd] Connection to 127.0.0.1:10000 failed (46ms)
Feb 16 00:25:22 192.168.1.3 got 129 cmd 9F
Feb 16 00:25:22 192.168.1.3 /dev/dvb/card0/demux0 error 2: No such file or directory
Feb 16 00:25:27 192.168.1.3 [ 00:25:31 ] [ Sci ] NO Card ATR data detected
Feb 16 00:25:27 192.168.1.3 [ 00:25:31 ] [ Loader ] Reset failed ...
Feb 16 00:25:27 192.168.1.3 [ 00:25:31 ] [ Loader ] Starting Newcamd Server on port 10000
Feb 16 00:25:27 192.168.1.3 [ 00:25:31 ] [ NewCS ] Ready to GO! :)
Feb 16 00:25:27 192.168.1.3 [ 00:25:31 ] [ Newcamd ] Newcamd thread Server started on port 10000
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ Box detect ] Box type 6 (Dream Multimedia (MIPS) Box)
Feb 16 00:26:25 192.168.1.3  for device 0 (lower) not present, defaulting to NO
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ Config ] /dev/sci0 ECM priority: round
Feb 16 00:26:25 192.168.1.3  not present, defaulting EMM: 20, ECM: Dynamic
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ Newcamd ] Server name : newcs
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ Newcamd ] Des key     : 0102030405060708091011121314
Feb 16 00:26:25 192.168.1.3  not present for User: dreambox, defaulting to NO
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] No username or password in user section, skipping...
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ Newcamd ] User 2: dreambox, Pass: dreambox, Host none, Port: 0, Au: On, Spider allowed: No, Sidoverride: No, level: 0
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ httpd ] httpd-user: newcs, password: newcs, accesslevel: admin
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ EMM Cache ] Initialising dynamic Cache
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] [ ECM Cache ] Initialising dynamic Cache
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] Calibrating delay loops
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] usleep(5) takes: 0 s 13 us
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] usleep(10) takes: 0 s 17 us
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] usleep(100) takes: 0 s 107 us
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] usleep(500) takes: 0 s 507 us
Feb 16 00:26:25 192.168.1.3 [ 00:26:30 ] Allocation memory for 200 regular users
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Loader ] Starting Telnet on port 0
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ SockSrv ] Server thread started
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Loader ] Started HTTP-server on port: 8080
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Loader ] Reader type 5 on node /dev/sci0
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Sci ] Closing device /dev/sci0 [Handle=-1]
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Sci ] Opening device /dev/sci0
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Sci ] No card present in reader
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Loader ] Reset failed ...
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Loader ] Starting Newcamd Server on port 10000
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ NewCS ] Ready to GO! :)
Feb 16 00:26:26 192.168.1.3 [ 00:26:30 ] [ Newcamd ] Newcamd thread Server started on port 10000
Feb 16 00:26:41 192.168.1.3 tuxbox mgcamd v1.31 by mixvt (compiled Oct 29 2008 19:11:00)
Feb 16 00:26:41 192.168.1.3 [mg] Net:1:1:2:5s Show ecm:1, emm:1 Up:0 Au:1 Dir:0 Osd:no:80:0 Cache:7 Log:1:192.168.1.2:514 Reread:0
Feb 16 00:26:41 192.168.1.3 [mg] Ecm cache time: 15
Feb 16 00:26:41 192.168.1.3 Box type: dreambox
Feb 16 00:26:41 192.168.1.3 /dev/dvb/card0/ca0 error 2: No such file or directory
Feb 16 00:26:41 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 16 00:26:41 192.168.1.3 SoftCam.Key error 2: No such file or directory
Feb 16 00:26:41 192.168.1.3 AutoRoll.Key error 2: No such file or directory
Feb 16 00:26:41 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 16 00:26:41 192.168.1.3 [config] newcamd route = dreambox:127.0.0.1:10000 server server
Feb 16 00:26:41 192.168.1.3 newcamd keep alive: 0, incoming port: 0
Feb 16 00:26:41 192.168.1.3 [mgcam] emm thread started
Feb 16 00:26:41 192.168.1.3 [mgcamd] tps update started.
Feb 16 00:26:41 192.168.1.3 /var/keys/tps.bin error 2: No such file or directory
Feb 16 00:26:41 192.168.1.3 [newcamd] Connecting to 127.0.0.1:10000...
Feb 16 00:26:41 192.168.1.3 [ 00:26:45 ] [ Newcamd ] new connection from 127.0.0.1 on socket 9
Feb 16 00:26:41 192.168.1.3 [ 00:26:45 ] [ Newcamd:10000 ] Connection from 127.0.0.1
Feb 16 00:26:41 192.168.1.3 [ 00:26:45 ] [ Newcamd:10000 ] User dreambox logged in, client: Mgcamd
Feb 16 00:26:41 192.168.1.3 [newcamd] Login to 127.0.0.1:10000 as dreambox accepted (0ms)
Feb 16 00:26:41 192.168.1.3 [newcamd] Card data from 127.0.0.1:10000 (0ms):
Feb 16 00:26:41 192.168.1.3 EMM enabled: UA yes SA yes GA yes, Card serial: 0
Feb 16 00:26:41 192.168.1.3 Userid 1 caid 0 providers 1
Feb 16 00:26:41 192.168.1.3 Idents: 000000
Feb 16 00:26:41 192.168.1.3 ids: 0
Feb 16 00:26:41 192.168.1.3 
Feb 16 00:26:41 192.168.1.3 got 129 cmd 9F
Feb 16 00:26:41 192.168.1.3 /dev/dvb/card0/demux0 error 2: No such file or directory
Feb 16 00:26:41 192.168.1.3 [ 00:26:46 ] [ Newcamd:10000 ] User dreambox logout

[MIRAGE]

Вот что в newcs.xml

<?xml version="1.0"?>
<newCSconfig>
<readers name="Dreambox SCI">
<device>
<name>?????? ???? ??????????????</name>
<type>sci</type>
<node>/dev/sci0</node> <!-- ??? ????????? ? 1 ??????????????? ???? ???? ???? ????? ???????????? -->
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<PTShandshake>No</PTShandshake> <!-- ??? ???? Viaccess ?????? ???????? Yes, ??? ???????? ???????? ?????? ?????-->
<carddetect>no</carddetect>
<newcamd_port>10000</newcamd_port> <!-- ???? ? ???????? ?? ????? ????????? ????? ? ????? ?????-->
<autosid>No</autosid>
<priority>round</priority>
</device>
<device>
<name>??????? ???? ??????????????</name>
<type>sci</type>
<node>/dev/sci1</node> <!-- ??????? ???? ?????????????? ????? ?????? ??? Dreambox, 7000,7020,7025,8000 -->
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<PTShandshake>No</PTShandshake>
<carddetect>no</carddetect>
<newcamd_port>10001</newcamd_port>
<autosid>No</autosid>
<priority>round</priority>
</device>
</readers>
<radegastserver>
<enabled>No</enabled>
<port>10003</port>
<allow>
<hostname>localhost</hostname>
</allow>
</radegastserver>
<cache>
<emm>20</emm>
<ecm>-1</ecm>
</cache>
<httpd>
<server>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>newcs</name>
<password>newcs</password>
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<password></password>
<mode>normal</mode>
<level>normal</level>
<type>init</type>
<output>console,tcp</output>
<tcp_port>1001</tcp_port>
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<enabled>Yes</enabled>
<name>newcs</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>local</name> <!-- ?????, ??? ????????? ??????? ???? ?? ?? MGcamd (????? ???? ?????) -->
<password>local</password> <!-- ??????, ??? ????????? ??????? ???? ?? ?? MGcamd (????? ???? ?????) -->
<hostname>192.168.1.3</hostname>
<au>on</au> <!-- ??????? ?????? ????? ?????????? ???????????? -->
</user>
<user>
<name>root</name> <!-- ?????, ??? ????????? ??????? (?????? ??????? ?? ????, ???? ????? ????????) -->
<password>azbox</password> <!-- ??????, ??? ????????? ??????? (?????? ??????? ?? ????, ???? ????? ????????) -->
<au>off</au> <!-- ???????? ?????? ????? ?????????? ???????????? -->
</user>
</newcamdserver>
</newCSconfig>

Это шутка? или серьезно?

Сообщение объединено:  16 февраля 2011, 01:49:58
А теперь серьезно, вы редактировать конфиг файлы похоже не умеете отсюда и такие ошибки, малотого в моем посте на 4 странице обратите внимание на красные строки, что я выделил.

[kazlift]

Изменил значение на Yes .Для верности перезагрузил ресивер.Всё равно не работает.

Feb 16 02:33:32 192.168.1.3 tuxbox mgcamd v1.31 by mixvt (compiled Oct 29 2008 19:11:00)
Feb 16 02:33:32 192.168.1.3 [mg] Net:1:3:2:4s Show ecm:1, emm:1 Up:5 Au:2 Dir:0 Osd:no:80:0 Cache:0 Log:1:192.168.1.2:514 Reread:0
Feb 16 02:33:32 192.168.1.3 [mg] Ecm cache time: 15
Feb 16 02:33:32 192.168.1.3 Box type: mips dreambox (dm7025, dm800)
Feb 16 02:33:32 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 16 02:33:32 192.168.1.3 SoftCam.Key error 2: No such file or directory
Feb 16 02:33:32 192.168.1.3 AutoRoll.Key error 2: No such file or directory
Feb 16 02:33:32 192.168.1.3 Conax.Key error 2: No such file or directory
Feb 16 02:33:33 192.168.1.3 [config] newcamd route = local:192.168.1.3:10001 server newcs
Feb 16 02:33:33 192.168.1.3 newcamd keep alive: 300, incoming port: 21000
Feb 16 02:33:33 192.168.1.3 [mgcam] emm thread started
Feb 16 02:33:33 192.168.1.3 [mgcamd] tps update started.
Feb 16 02:33:33 192.168.1.3 /var/keys/tps.bin error 2: No such file or directory
Feb 16 02:33:33 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 16 02:33:33 192.168.1.3 [newcamd] Connection to 192.168.1.3:10001 failed (48ms)
Feb 16 02:33:36 192.168.1.3 got 124 cmd 9F
Feb 16 02:33:36 192.168.1.3 [mg0] namespace 1680000 t-id D on-id 70
Feb 16 02:33:36 192.168.1.3 [mg0] descramble on 5, source 2
Feb 16 02:33:36 192.168.1.3 [mg0] service 3336 index 0 pmt pid 51E (1)
Feb 16 02:33:36 192.168.1.3  CaPID: 0x07DA ProvID: 040600
Feb 16 02:33:36 192.168.1.3  CaPID: 0x0FAA ProvID: 023700
Feb 16 02:33:36 192.168.1.3 [mg0] No viaccess key(s) found for id 40600 keynr 08
Feb 16 02:33:36 192.168.1.3 [mg0] network can't decode
Feb 16 02:33:36 192.168.1.3 [mg0] pid 0x07DA failed to decode.
Feb 16 02:33:36 192.168.1.3 [mg0] No viaccess key(s) found for id 23700 keynr 08
Feb 16 02:33:36 192.168.1.3 [mg0] network can't decode
Feb 16 02:33:36 192.168.1.3 [mg0] pid 0x0FAA failed to decode.
Feb 16 02:33:36 192.168.1.3 [mgcamd] emm started
Feb 16 02:33:36 192.168.1.3  CaPID: 0x03EC ProvID: 040600
Feb 16 02:33:36 192.168.1.3  CaPID: 0x03E8 ProvID: 023700
Feb 16 02:33:36 192.168.1.3  CaPID: 0x03EB ProvID: 030600
Feb 16 02:33:36 192.168.1.3  CaPID: 0x03ED ProvID: 040610
Feb 16 02:33:36 192.168.1.3  CaPID: 0x03EA ProvID: 040620
Feb 16 02:33:36 192.168.1.3 [mgcamd] emm stopped
Feb 16 02:33:52 192.168.1.3 [newcamd] Connecting to 192.168.1.3:10001...
Feb 16 02:33:52 192.168.1.3 [newcamd] Login to 192.168.1.3:10001 as local accepted (0ms)
Feb 16 02:33:52 192.168.1.3 [newcamd] Card data from 192.168.1.3:10001 (1ms):
Feb 16 02:33:52 192.168.1.3    EMM enabled: UA yes SA yes GA yes, Card serial: 0
Feb 16 02:33:52 192.168.1.3    Userid 1 caid 0 providers 1
Feb 16 02:33:52 192.168.1.3    Idents: 000000
Feb 16 02:33:52 192.168.1.3    ids: 0
Feb 16 02:33:52 192.168.1.3 



Судя по выделенному,не может подключиться к карте,я прав?

[Metabox1]

kazlift
В теме есть ответ и конфиги, смотри с первой страницы.